Application Note | Large Sample Profilometry

High-Speed Surface Characterization of an Oyster Shell

Patching Multiple Scans to Capture a Large, Curved Biological Sample Without Fixtures

Oyster shell on a high-speed profilometer stage

Research & Experimental Testing

Xavier Herrera-Keehn & Jocelyn Esparza

Visual Design & Editorial

Andrew Shore

Introduction

Large samples with complex geometries can prove difficult to work with due to sample preparation, size, sharp angles, and curvature. In this study an oyster shell will be scanned to demonstrate the NANOVEA HS2000 Line Sensor’s capability to scan a large, biological sample with complex geometry. While a biological sample was used in this study, the same concepts can be applied to other samples.

Why 3D Non-Contact Profilometry Matters on an Oyster Shell

By scanning the whole surface of an oyster shell, the NANOVEA HS2000 Line Sensor will display its ability to work with large samples with unique geometries. Typically, samples need to be securely mounted to the stage to mitigate their displacement as the stage moves. This usually requires additional sample preparation or a fixture to be used. But with the smooth air bearing stages on the NANOVEA HS2000, little to no sample preparation is needed to begin your tests.

Patching, shown in this study, allows the NANOVEA HS2000 Line Sensor to capture a surface that has features taller than the optical sensor’s height range or the instrument’s lateral range. This is accomplished by taking multiple scans at varying heights and overlaying them at their relative offsets. And with the stages’ 3 axis motion control, you can index in specified steps in the z direction to quicken the process.

Oyster shell resting on the air-bearing stage under the HS2000 line sensor

Measurement Objectives

In this application, an oyster shell was scanned using the NANOVEA HS2000 Line Sensor. Multiple scans were conducted at various heights and reconstructed via patching to represent the whole shell.

NANOVEA ST500 Large Area

Optical 3D Profilometer

NANOVEA ST500 large area optical profilometer for non-contact 3D surface measurement

Measurement Parameters

Oyster shellValue
Optical penL3
Acquisition rate400 pps
Averaging1
Measured surface140 mm × 90 mm
Step size25 µm × 25 µm
Measurement time00:05:31 (h:m:s)

Table 1: Test parameters used for each of the 9 scans performed for this study.

Grey oyster shell on a wooden surface
Sample of oyster shell tested.

Results

Series of Surfaces

For this study, a total of 9 scans were conducted on the oyster shell to obtain height data over the whole surface. The individual scans are shown in a 3D view below.

3D view of the nine overlapping scans of the oyster shell at different heights
Fig. 1: The nine individual scans in 3D view.

3D Surface

The patched 2D and 3D surface can be observed below. We were able to obtain the whole surface of the oyster shell with the NANOVEA HS2000 Line Sensor without compromising on the resolution. Small features on the shell’s surface can still be seen in the 3D view.

Oyster shell photo with its patched false-color 2D height map, ISO 25178 parameters and 3D view
Fig. 2: Patched 2D and 3D surface of the oyster shell.

Surface Roughness Analysis

Below is the surface roughness of the oyster shell, this was obtained by applying a gaussian filter of 1.5 mm. This excludes form (or waviness) larger than the cut-off index, leaving behind features that represent the oyster shell’s roughness. Despite the lack of a fixture, stage noise was not observed in the surface roughness analysis.

Oyster shell photo with its roughness map after form removal, ISO 25178 parameters and 3D view
Fig. 3: Surface roughness of the oyster shell (1.5 mm Gaussian filter).
ISO 25178 parameterWhole surface (Fig. 2)Roughness (Fig. 3)
Sa5.054 mm0.1255 mm
Sq6.058 mm0.2614 mm
Sp17.52 mm3.987 mm
Sv12.38 mm1.211 mm
Sz29.90 mm5.198 mm
Ssk0.028773.737
Sku2.28141.93

Table 2: Height parameters of the patched surface and of its roughness.

Conclusion

A total of 9 scans were used in this study to recreate the surface of the oyster shell using the NANOVEA HS2000 Line Sensor. From the patched surface, the roughness of the oyster shell was measured by removing the form (or waviness) of the sample. Patching can also be used to measure much finer roughnesses on a large sample that would normally be beyond the optical sensor’s height range. Large conical lenses, for example, require a very fine step size in order to quantify microscopic features that can be present. The NANOVEA HS2000 Line Sensor has shown it is able to conduct profilometry measurements on large samples with abnormal geometries while retaining high resolution with minimal sample preparation.

Oyster shell under the HS2000 line sensor in the lab

Frequently Asked Questions About Scanning Large, Complex Samples

What makes large, curved samples difficult to profile?

Sample preparation, size, sharp angles and curvature. Samples usually need secure mounting so they do not move with the stage, which can require extra preparation or a fixture.

What is patching in profilometry?

Patching captures a surface with features taller than the optical sensor’s height range or wider than the lateral range by taking multiple scans at different heights and overlaying them at their relative offsets. Indexing in set Z steps speeds this up.

How was the oyster shell scanned?

Nine scans with the L3 optical pen at 400 pps and a 25 µm × 25 µm step, each over 140 mm × 90 mm in 5 minutes 31 seconds, were patched to reconstruct the whole shell.

Does the sample need a fixture?

Little to no preparation was needed: the HS2000’s smooth air-bearing stages kept the unfixed shell steady, and no stage noise appeared in the roughness analysis.

How is roughness separated from the shell’s shape?

A 1.5 mm Gaussian filter removes form and waviness larger than the cut-off. The whole surface measured Sa 5.054 mm, while the roughness after filtering was Sa 0.1255 mm.

Where else is patching useful?

Patching can measure much finer roughness on large samples beyond the sensor’s height range, for example large conical lenses that need a very fine step to quantify microscopic features.

Need 3D Scanning of Large or Complex Parts?